Merlin MT600 Instructions d'exploitation télécharger pdf (Page 19)

SPECIFICATIONS

Input Voltage........... 230-240 VAC, 50Hz

Max. Pull Force....... 600N (MT600), 1000N (MT1000)

Power...................... 6Nm (MT600), 10Nm (MT1000)

Watts ....................... 130W (MT600), 190W (MT1000)

Standby Power........ 3 Watts nominal

Motor

Type ........................ DC gearmotor permanent

lubrication

Drive Mechanism

Drive........................ Chain/belt with two-piece trolley on

steel rail.

Length of Travel ...... Adjustable to 3.0 metres

Travel Rate.............. 5"-7" (127-178mm) per second

Lamp ....................... On when door starts, off 2-1/2

minutes after stop.

Door Linkage........... Adjustable door arm. Pull cord

trolley release.

Safety

Personal.................. Push button and automatic stop in

down direction. Push button and

automatic stop in up direction.

Electronic ................ Automatic force adjustment

Electrical.................. Transformer overload protector and

................................ low voltage push button wiring.

Limit Device ............ Optical RPM/Passpoint detector.

Limit Adjustment...... Electronic, semi and fully automatic.

Start Circuit ............. Low voltage push button circuit.

Dimensions

Length (Overall) ...... 3.2m (122-1/2")(with Standard rail)

Headroom Required 30mm

Hanging Weight....... 9.5kg

Receiver

Memory Registers... 16 (MT600), 64 (MT1000)

Operating Frequency 433.92MHz

Your opener can be activated by any of the following devices:

• The Lighted Door Control Button. Hold the button down until door

starts to move.

• The outside keyswitch or keyless entry system (if you have

installed either of these accessories).

• The Transmitter. Hold the push button down until the door starts to

move.

Opening the Door Manually:

The door can be opened manually by pulling the release handle

down. To reconnect the door, pull the release handle down and toward

the opener.

Do not use the manual release handle to pull the door open

or closed. When the opener is activated by transmitter or door

control button:

1. If open, the door will close. If closed, the door will open.

2. If closing, the door will stop.

3. If opening, the door will stop (allowing space for entry and exit of

pets and for fresh air).

4. If the door has been stopped in a partially open or closed position,

it will reverse direction.

5. If an obstruction is encountered while closing, the door will reverse.

6. If an obstruction is encountered while opening, the door will reverse

and stop.

7. The optional Protector System™ uses an invisible beam which,

when broken by an obstruction, causes a closing door to open

and prevents an open door from closing. It is STRONGLY

RECOMMENDED for homeowners with young children.

Allow a 15 minute cooling period after 5 continuous operations

of the opener.

The opener light will turn on:

1. when opener is initially plugged in;

2. when the power is briefly interrupted;

3. when the opener is activated.

The light turns off automatically after 2-1/2 minutes. Bulb size is

230V/40W maximum.

OPERATION OF YOUR OPENER

When properly installed your opener will operate with minimal

maintenance. The opener does not require additional lubrication.

Limit and Force Settings: These settings must be checked and

properly set when opener is installed. Weather conditions may cause

some minor changes in the door operation, requiring some re-

adjustments, particularly during the first year of operation.

Refer to Setting the Limits and Force sections 22 and 23. Follow the

instructions carefully and repeat the safety reverse test after

any adjustment.

Transmitter: The transmitter may be secured to a car sun visor with

the clip provided. Additional transmitters can be purchased at any time

for use in all vehicles using garage. Refer to Accessories. Any new

transmitters must be programmed into the opener.

Transmitter Battery: If transmission range lessens, replace battery.

To Change Battery: To replace batteries, use the visor clip or

screwdriver blade to pry open the case. Insert batteries positive side

up. To replace cover, snap shut along both sides. Do not dispose of

the old battery with household waste. Take batteries to a proper

disposal centre.

CARE OF YOUR OPENER

Once a Month:

• Repeat safety reverse test. Make any necessary adjustments.

• Manually operate door. If it is unbalanced or binding, call for

professional garage door service.

• Check to be sure door opens and closes fully. Set limits and/or force

if necessary.

Once a Year:

• Oil door rollers, bearings and hinges. The opener does not require

additional lubrication. Do not grease the door tracks.

• GREASE THE RAIL AND THE TROLLEY.

MAINTENANCE OF YOUR OPENER

Door should be fully closed if possible. Weak or

broken springs could allow an open door to fall

rapidly. Property damage or serious personal

injury could result.

SPECIAL NOTE: Chamberlain strongly recommends that The Protector System

(IR Beams) be installed on all garage door openers.

1 2 ... 14 15 16 17 18 19 20

Commentaires sur ces manuels

Pas de commentaire

Merlin MT600 Instructions d'exploitation Page 19

Commentaires sur ces manuels

Produits connexes et manuels pour Ouvreur de porte de garage Merlin MT600